Drafty rooms, a hot upstairs or cold floors usually come from gaps and thin insulation. We seal first, then insulate where it counts.
Home insulation in Seaside means sealing the air leaks in your house and adding insulation where it's thin, in the attic, floors, crawl space and walls, so each room holds the temperature you set and less of the heat you pay for slips out.
Most people call us because something feels off, like a drafty bedroom, a hot upstairs in late summer or the room over the garage that never warms up, and they can't tell whether the attic, the floor or the walls are to blame. The price depends on how big the house is, which areas need work, how easy they are to get into, whether old insulation has to come out first and how much attic air sealing goes with it. The schedule depends on the same things, plus any repair that has to happen before we start, like a roof leak or old wiring, and a permit if your job needs one. Your own figure comes on the estimate, once I've seen the house.
I come out to look at the job and write the estimate myself, so the number reflects what's actually in your attic and under your floor. Our installers do the work, and when they're done I walk through it with you so you know exactly what we did and why.
Before I started this business in 2023, I spent years doing upkeep for a property management company, crawling through attics and under floors. That's where I learned to look for leaks and damp before adding anything, and it's why property managers call us too.
We're licensed and fully insured. That matters in an attic, where our installers are working around wiring, framing and the ceiling over your living room, and it means you aren't the one carrying the risk while we're in your house.
If there's a roof leak or old wiring that should be fixed before we insulate, I'll tell you, because insulation laid over a problem just hides it. Our work is backed by our satisfaction guarantee. Call (831) 204-4546 when you're ready to talk it through.
We reply within one business day to set a time, and the on-site estimate is free with no obligation. I come out myself, walk the house with you and write up what I'd do and what it costs. It helps if you note the rough size of your attic, the rooms that bother you and any gaps you've noticed around windows, doors, vents or pipes.
The city recommends that owners ask its Building Department, at the permits and inspections counter in City Hall, about permits before any building project or major repair, so that's where the permit question for your insulation job gets answered. Before we start, we check with the city or county building office for your address, and where a permit is needed, we take care of the paperwork and set up the inspections. Work in Seaside follows the state building codes plus the city's own changes to them, and the state's energy rules cover work on houses already standing, with standards that vary by climate zone.
Around Seaside we mostly find older houses with thin, settled insulation in the attic, raised floors over crawl spaces that feel cold underfoot, and damp coastal air that makes those clear eave vents matter. We're based in Seaside and work in cities across Monterey County, into Santa Cruz County and over to Gilroy, including Monterey and Marina, and if you're not sure we come out your way, just ask.
Attic insulation across the US usually costs about $1 to $3 per square foot, and that's the national going rate for attic work, not our price. A whole house with walls or a crawl space works out differently than an attic alone. Your own number comes from the estimate, after I've seen what's up there.
Federal energy guidance says homes save up to 15% on heating and cooling, on average, by adding insulation and sealing air leaks. The same guidance puts total energy savings at up to 11%. Those are national averages and upper ends, so they're worth weighing against the cost, but your house's starting point matters more than any average.
Start by knowing the basic types, because that makes it easier to compare what each installer proposes. The state's energy office names four for homes: batts or blankets, loose fill, spray foam and rigid board. Batts fit open framing, loose fill covers attic floors well, spray foam seals as it insulates, and rigid board suits foundation walls and rim joists.
Choose the installer as carefully as the material, because federal guidance says insulation performance depends heavily on how well it's installed. Ask whether they'll look at the whole space before quoting and how they'll handle gaps and vents. California's Contractors State License Board has a C-2 classification for insulation work, so it's fair to ask which license a contractor holds.
Time in the attic depends mostly on its size, how easy it is to reach and whether old insulation comes out first, and I'll lay that out with the estimate. With loose fill or batts you can usually stay home while we work. Spray foam is different, because the foam maker sets how long everyone, kids and pets included, stays out before coming back in, and we go over that with you before the day.
